StudioSpares 18\" T/S PDF

  • nickyburnell
  • Topic Author
  • Offline
  • Platinum Member
  • Platinum Member
More
16 years 3 months ago #3940 by nickyburnell
StudioSpares 18\" T/S PDF was created by nickyburnell
www.mediafire.com/?hvy1gjo4hnt

Very, very helpful company, SoundKing.
And here, so called Pro suppliers don't even answer the phone.
No wonder.............

Please Log in or Create an account to join the conversation.

  • nickyburnell
  • Topic Author
  • Offline
  • Platinum Member
  • Platinum Member
More
16 years 3 months ago #3958 by nickyburnell
Replied by nickyburnell on topic StudioSpares 18\" T/S PDF
Bump. So expert people, how bad is this now the translation is confirmed?
Thanks

Please Log in or Create an account to join the conversation.

More
16 years 3 months ago #3959 by tony.a.s.s.
Replied by tony.a.s.s. on topic StudioSpares 18\" T/S PDF
Nick, what is all this Mediafire stuff all about. I thought I was going into a speaker site.

Peace and goodwill to all speaker builders

Please Log in or Create an account to join the conversation.

  • nickyburnell
  • Topic Author
  • Offline
  • Platinum Member
  • Platinum Member
More
16 years 3 months ago #3960 by nickyburnell
Replied by nickyburnell on topic StudioSpares 18\" T/S PDF
It's only a hosting site, same as rapid share etc. You use them to share files. The PDF of the T/S is there to download. It's not possible to post the PDF here and as it was emailed to me direct from SK there was no other way of shareng it.
I understand your concern though, can't be too careful.
Here are the T/S detailf from the PDF, if anybody would like the plot as well, but doesn't like file hosting sites, PM me an email address and I'll forward the PDF.

Freq Range 33hz -1.8khz
Revc: 5.2ohm
Zmax 87.82ohn
SPL 95db
Qts 0.49
f 33.27hz
sd 0.128cm to the power of 3
Qms 8.34
Vas 278.5L
Mms 191.1g
Mmd 164.86g

Nick

Please Log in or Create an account to join the conversation.

More
16 years 3 months ago #3963 by studio45
Replied by studio45 on topic StudioSpares 18\" T/S PDF
the sd figure is in the wrong units it should be metres squared not centimetres cubed. is it 0.128 m2 then? which would be 1280 cm2? that's a nice big cone

Please Log in or Create an account to join the conversation.

  • nickyburnell
  • Topic Author
  • Offline
  • Platinum Member
  • Platinum Member
More
16 years 3 months ago #3968 by nickyburnell
Replied by nickyburnell on topic StudioSpares 18\" T/S PDF
Could be in the translation?

I'll try and extract the plot from the pdf

Please Log in or Create an account to join the conversation.

More
16 years 3 months ago #3988 by deadbeat
Replied by deadbeat on topic StudioSpares 18\" T/S PDF
It would be 1280 cm2 being an 18. Just a typo.

Beranek\'s law
\'bits of ply round a driver\'

Please Log in or Create an account to join the conversation.

  • nickyburnell
  • Topic Author
  • Offline
  • Platinum Member
  • Platinum Member
More
16 years 3 months ago #3993 by nickyburnell
Replied by nickyburnell on topic StudioSpares 18\" T/S PDF
So how bad are they?

Please Log in or Create an account to join the conversation.

Time to create page: 0.333 seconds
Powered by Kunena Forum